Dinamap Pro 100V2 Instrukcja Obsługi Strona 30
- Strona / 104
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
2-8 PRO 100-400 V2 Patient Monitor Service Manual Revision A
2009829-001
Product Description: SECTION 2. PRODUCT DESCRIPTION
16. ON/OFF switch: Controls on/off state of PRO Monitor; push for
power on and push again for power off.
17. Battery power indicator: Yellow LED indicates operation and
charge status of battery.
18. SpO
2
sensor connector: SpO
2
sensor extension cable attaches
here (Models 300 and 400).
19. Mean arterial pressure display: 3-digit red LED indicates
measured MAP in mmHg and shows instantaneous cuff pressure
during BP determination.
20. SpO
2
pulse indicator: Yellow LED in heart symbol flashes to
indicate that real-time pulse rate measurements are being derived
from SpO
2
signals (Models 300 and 400).
21. Rotor: Used to highlight and select items in LCD menus; if monitor
is off, pressing rotor will switch monitor on.
22. Pulse BPM display: 3-digit yellow LED shows pulse rate in beats
per minute.
23. SpO
2
display: 3-digit red LED indicates oxygen saturation in %
(Models 300 and 400).
24.SpO
2
motion/artifact indicator LED: For NELLCOR, LED
Illuminates when motion artifact is detected (Models 300 and 400).
For Masimo, LED illuminates when low perfusion or low signal quality
is detected (Models 300 and 400).
25. LCD (liquid crystal display): Displays all alarms, user interface
messages, and configuration options.
26. Alarm silence switch: Alternately mutes and enables audible
alarms; when pushed once after alarm sounds (silence on), the
switch illuminates to indicate that audible alarms have been silenced
for 2 minutes.
27. AUTO BP key: Press to start Auto BP mode.
28. Light sensor: Automatically measures ambient light to set LED
display intensity.
29. START/STOP BP key: Press to start or stop a BP, Auto, Stat, or
Vitals determination.
30. Cuff connector: BP cuff hose attaches here.
Not Shown: The printer access door is located on the left side of the
monitor. Push the latch to open the door and access the paper supply
and print head. For details, see Section 5, Component Information.
- PRO Series 100 - 400 V2 1
- Service Manual 1
- PRO 100-400 V2 3
- Patient Monitor 3
- PRO 100-400 Patient Monitor 5
- Table of Contents: 10
- 1 Introduction 11
- For your notes 12
- Table of Contents 13
- 2009829-001 14
- Section 1. INTRODUCTION 15
- 1.2. ADDENDA 16
- 1.4. SERVICE POLICY 16
- 1.5. EXTENDED WARRANTIES 16
- 1.6. ASSISTANCE 16
- 1.7. SERVICE 17
- 1.9. WARNINGS AND PRECAUTIONS 18
- 1.10. SYMBOL DEFINITIONS 19
- 2 Product Description 23
- Product Description: 26
- 2.1. INTRODUCTION 27
- 2.2. PRODUCT CONFIGURATIONS 27
- 2.5. COMPATIBLE PARTS 32
- 2.6. SPECIFICATIONS 34
- 2.6.3. Mechanical 35
- 2.6.4. BP 35
- 2.6.5. TURBO TEMP 36
- 2.6.6. SpO 36
- Nellcor Patents 37
- Masimo Patents 39
- 3 Theory of Operation 41
- Theory of Operation: 44
- 3.1 INTRODUCTION 45
- 3.2.4 Host Communication Port 46
- 3.3 FUNCTIONAL DESCRIPTION 47
- 3.3.4 SPO2 PWA (Optional) 48
- 3.3.6 LCD Assembly 49
- 3.3.7 Printer PWA w/Printer 49
- 4 Calibration & 53
- 4.1 INTRODUCTION 57
- 4.2. FUSES 57
- 4.3. PERIODIC MAINTENANCE 57
- 4.3.2. Power Up Checks 58
- 4.3.5. Checking Calibration 59
- 4.4 Clinician Mode 60
- 4.4.3. Clinician More... Menu 62
- 4.5. SERVICE MODE 63
- 4.5.2 Service Mode Main Menu 64
- 4.5.3. NIBP Menu 65
- 4.5.4. System Menu 66
- 4.6.1. SpO 68
- Checks (PRO 300 & 400) 68
- 4.6.2. Leak Test 69
- 4.6.3. NIBP Calibration Check 70
- 4.6.7. Printer Test 73
- plug with the 77
- 5 Schematics & Drawings 79
- Field Replaceable Parts 82
- Description Part Number 85
- PRO 100-400 Assembly Drawing 87
- Front Case Drawing 87
- Shown with Temp Assembly 87
- Page 1 of 3 87
- Page 2 of 3 88
- Shown with Masimo Board 89
- Page 3 of 3 89
- Rear Case Drawing 90
- Page 1 of 4 90
- Page 2 of 4 91
- Pnuematic Assembly Drawing 92
- Page 3 of 4 92
- Pneumatic Hose Routing 93
- Page 4 of 4 93
- Sheet 1 of 9 94
- Sheet 2 of 9 95
- Sheet 3 of 9 96
- Sheet 4 of 9 97
- Sheet 5 of 9 98
- Sheet 6 of 9 99
- Main Board Assembly 100
- P/N: 2008238-001 C 100
- Sheet 7 of 9 100
- ISOLATED POWER SUPPLY 101
- HOST INTERFACE CONNECTOR 102
- SPO2 PATIENT CONNECTOR 102
- SPO2 MODULE CONNECTOR 102
- 2009829-001 A 104
Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Dinamap Pro 100V2
(108 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji